Trusted by 200,000+ creators & businesses in 80+ countries — Get a Free Quote Today

Which Laser Engraver for a Small Business? xtool F1 Ultra vs. CO2 CNC vs. Used

There's no "best" laser engraver — only the best for your work

I get asked this constantly: "Which laser engraver should we buy?" And I've stopped giving a single answer. Because after five years of managing equipment procurement for a fabrication company — roughly $180,000 annually across a dozen vendors — I've learned the honest answer is always: it depends on what you're actually cutting.

The three machines that come up in almost every conversation are the xtool F1 Ultra (dual fiber + diode laser), a CO2 CNC laser (the big-bed workhorses), and a used laser engraver (for tight budgets). Each one is the right answer for a different scenario. And — this is the part that took me a while to accept — the most expensive option isn't always the worst TCO. Sometimes it's the cheapest.

Here's how I break it down now.

Scenario 1: You cut metal, mark tools, or do deep engraving

If your work involves stainless steel sheets, aluminum tags, tools, or anything that needs a permanent mark on metal, you need a fiber laser. Full stop. Diode lasers (the cheap ones) will burn coating on metal but won't actually cut or deep-engrave it.

This is where the xtool F1 Ultra earns its place. It runs a 20W fiber laser and a 20W diode laser in one enclosure. The fiber side handles metal cutting and deep engraving; the diode side handles the usual wood, leather, and acrylic. It also does color engraving on stainless — the kind of thing that gets clients to pay a premium for "custom" work.

What I tell people: if metal is more than about 30% of your workload, the dual-laser route usually wins on TCO. Yes, the sticker price is higher than a pure diode machine. But if you'd otherwise be outsourcing metal work — or turning it down — the payback is honestly not that long. I've seen small shops pay back the difference in four to six months on a few regular metal-marking accounts. That's my experience, at least, with our supplier base.

One caveat: the F1 Ultra is a desktop unit with a modest work area. If you're cutting full 4×8 sheets, this is not your machine. It's for parts, tags, small runs, and prototyping.

"I didn't fully understand the difference between 'marks metal' and 'cuts metal' until a $3,000 order came back wrong."

That was my rookie mistake, in year one. I assumed any laser could do metal because the brochure said "metal marking." It couldn't cut. We lost the job.

Scenario 2: You mostly cut acrylic, wood, leather, and glass

If your material list is 90% organics — acrylic signage, wood signage, leather goods, glass etching — a CO2 CNC laser is usually the better economics. You get a much larger bed for the money, and CO2 watts are cheaper than fiber watts.

A basic 40–60W CO2 CNC desktop unit typically lists between $2,500 and $4,000 as of early 2025 (I'd verify — prices move). That gets you a bed size that a dual-laser desktop unit can't match. For a shop cutting acrylic sheets or doing wooden signage at volume, that's the right tool.

Here's the contrarian part: a lot of buyers assume "fiber" is always better because it's newer and more expensive. It's not. For pure acrylic and wood work, a CO2 will often outperform a fiber laser on speed and cost per part. Buying a dual-laser unit when you don't cut metal is overpaying for capability you'll never use.

Now, glass engraving settings are a different story. The xtool F1 Ultra does glass, but glass is one of those materials where settings vary wildly by composition and coating. There is no universal "glass setting." Anyone who tells you there is either hasn't tested enough or is selling you something. Test on scrap first. I usually budget 5–10 test pieces per new glass supplier.

CO2 lasers have their own TCO trap: tube replacement. A CO2 tube is a consumable. Figure $300–$800 every 2–5 years depending on usage, plus alignment time. Budget it.

Scenario 3: You're on a tight budget and doing small runs

Here's where I'll be blunt, because I've been burned: a used laser engraver is often more expensive than a new mid-range one. Not always — but often enough that I now treat "used" as a last resort, not a smart-money move.

"A $500 quote turned into $800 after shipping, setup, and revision fees. The $650 all-inclusive quote was actually cheaper." I've watched this play out with lasers too. A used unit at 50% of new price looks great until you need a $400 tube, a $200 lens, and a controller board that the manufacturer discontinued in 2021. Suddenly your $2,000 used machine has a $3,200 TCO and no warranty.

This is the TCO calculation most people skip. The sticker is the easy part. The real number is:

  • Purchase price
  • Shipping and rigging (desktop units are heavy; freight isn't free)
  • Consumables (tubes, lenses, focus lenses, honeycomb beds)
  • Maintenance and downtime
  • Rework and scrap (especially in your first month)
  • Software and licensing (some used units transfer, some don't)

When I compare a used unit at $2,000 to a new entry-level machine at $3,000, I now assume the used unit will need $800–$1,200 in parts and setup in year one unless I know the seller personally. Run the number both ways before you commit.

That said — if you can inspect the unit, verify tube hours, confirm software transfer, and the seller lets you test-cut, used can work. I've done it twice successfully. I've also done it once badly. The difference was inspection.

How to tell which scenario you're in

Don't start with the machine. Start with your material list and your volumes. Answer these honestly:

  1. What percentage of your work involves bare metal cutting or deep engraving? Above ~30%, lean dual-laser (F1 Ultra class). Below 10%, a diode or CO2 is probably enough.
  2. What's your largest common part size? If it fits on a desktop bed, fine. If not, you need a CO2 with a big bed — no desktop unit will help.
  3. Do you need a warranty and support, or can you fix things yourself? Warranty and support have real value. If you're not technical, the used route is a trap.
  4. What's your realistic monthly volume? Low volume + occasional metal = dual-laser desktop. High volume + organics = CO2. Low volume + tight budget = save longer, buy new entry-level, skip used unless you can inspect.

I'm not 100% sure the 30% threshold is right for every shop — it's a rule of thumb from our own numbers, not a standard. But the principle holds: pick the machine that matches your material mix, then run TCO, then — and only then — look at the sticker.

One last thing. The "best small business laser engraver" question gets asked like there's a trophy. There isn't. There's a machine that fits your jobs and one that doesn't. I'd rather buy the right older design than the wrong new one. And I'd rather pay $650 all-in than $500 with surprises.

Share:
This entry was posted in Blog. Bookmark the permalink.
Jane Smith
Jane Smith

I’m Jane Smith, a senior content writer with over 15 years of experience in the packaging and printing industry. I specialize in writing about the latest trends, technologies, and best practices in packaging design, sustainability, and printing techniques. My goal is to help businesses understand complex printing processes and design solutions that enhance both product packaging and brand visibility.

Leave a Reply